Every morning the front door key needs the same little dance: push in, lift, wiggle, turn. It has been getting worse for a year, and this week it took three tries in the cold before the deadbolt finally gave.
A replacement lock has to fit holes that already exist, and that is where the visit begins. The locksmith measures the backset, the distance from the door edge to the centre of the bore, which on most doors is 60 or 70 millimetres, checks the cross-bore diameter and edge-bore size, notes door thickness and handing, and looks at the strike cut-out. Most residential hardware is made to these standard preparations, so the new lock usually drops into place with no new drilling. Where a mortise lock or a thick door departs from the norm, filler plates, extension kits or a careful new bore bring the door up to standard.
Sound familiar?Princess Margaret
Lock Replacement & Upgrade · Princess Margaret
Scene 1
A new lock inherits whatever the door and frame are doing, so both get a look. The locksmith checks whether the door has dropped on its hinges, whether weatherstrip is pushing it out of square, and whether the bolt lands squarely in the strike pocket or rubs its edge. The pocket depth matters as well: a bolt that reaches the back of a shallow pocket is not fully thrown. Hinge screws, a jamb split from an old forced entry and a strike held by short screws are all noted, because the visit will tidy them up so the new hardware works as designed.
Scene 2
Most modern latches and bolts adjust between the two common backsets, so the unit is set to the measured figure and slid into the edge bore. A spring latch goes in with its bevel facing the strike, while a deadbolt is oriented the way its markings or instructions call for, not by that bevel rule. The faceplate should sit flush in its mortise; where the old cut-out differs in shape or size, the mortise is trimmed with a sharp chisel, or a round drive-in collar is used where the door was prepared that way. The bolt is checked to travel freely before anything else goes on, since a bolt that binds in the door will bind under the key too.
Scene 3
Before the tools go back in the van, each lock is operated from both sides with the door open, then closed, then closed hard against the weatherstrip. The latch should catch on its own when the door swings shut, the deadbolt should throw to its stop with a fingertip on the thumb-turn and no shoulder on the door, and the key should turn without lifting or jiggling. You are invited to try each one yourself and to lock up behind the locksmith. Anything that felt marginal has been adjusted, so the door you close that night behaves the same as the one you tested.
What shapes the quoteBloordale Gardens Lock & Key Co.
FeesSame any hour
Photographs of each lock from outside and inside, plus one of the door edge showing the latch plate and one of the strike on the frame, tell the locksmith most of what they need. Add the door thickness if you can measure it, whether the door is wood, steel or fibreglass, the finish you want to match, how many doors are involved and whether you want them all on one key.
Yes, provided the cylinders share a compatible keyway, which the locksmith checks when choosing hardware. New cylinders are pinned on site to a single new key and any existing locks worth keeping are repinned to match. Front, back, side and garage doors commonly end up on one key, and a shed or gate padlock can join them. You then decide how many copies exist and who holds each.
The lock hardware is the same; the door construction changes the method. Steel and fibreglass doors have a wooden or composite block inside the lock stile, and existing bores are used wherever possible. Where a new deadbolt must be added, the locksmith drills with a jig and bits suited to the skin so the hole is clean and square, and fits an edge plate designed for that door. Insulated doors also move less with humidity, so alignment tends to hold well.
TorontoOntario
Lock Replacement & Upgrade · Toronto, Bloordale Gardens, Eringate, Etobicoke, Glen Agar, Islington, Thorncrest Village, West Deane Park
Every square is one home in a hundred.
On-site assessment
Every morning the front door key needs the same little dance: push in, lift, wiggle, turn.
(289) 804-4797, open 24/7.
On-site assessment preferred · (289) 804-4797, open 24/7
